Unpiggable Pipeline
Inspection

In pipeline and process integrity management, few words carry as many consequences as “unpiggable”. Once the label is applied, an asset tends to drop out of the inspection regime altogether: no baseline, no trend data and no way of detecting deterioration until it shows up as a process problem or a failure. This guide explains what makes a pipeline unpiggable, what accepting that label really costs, and how modern single-bodied intelligent pigs now make most of these assets inspectable without modification.

What makes a pipeline “unpiggable”?

Conventional in-line inspection relies on long, multi-bodied tools and dedicated launch and receive facilities. Many pipelines simply were not designed with that in mind. Common reasons a pipeline is classed as unpiggable include:

  • Diameter or schedule changes along the line
  • Short or tight-radius bends
  • T-pieces, branches or complex tie-ins
  • Short pipeline lengths
  • Limited or no breaks to install conventional launchers and receivers
  • Economics that do not justify mobilising a large multi-bodied inspection spread

In most cases the constraint is the tool, not the pipe. The unpiggable designation usually reflects the limits of a previous generation of inspection technology rather than any physical impossibility.

The cost of accepting the label

A gap in the integrity programme

A robust integrity programme depends on traceable, repeatable data that shows how condition changes over time. Assets that sit outside it introduce uncertainty that cannot be managed away with conservative assumptions or extra inspection elsewhere.

Risk that can only be estimated

Without inspection data, risk cannot be quantified, only estimated, and estimated risk is hard to defend to regulators, insurers and internal governance teams. Operators may understand an asset’s operating conditions, but they cannot demonstrate its actual integrity.

A cost deferred, not avoided

Uninspected assets are often seen as a cost avoided. In reality the cost is deferred and grows over time. Deterioration that could have been found early and fixed during a planned turnaround instead goes undetected until it demands a reactive, more expensive and more disruptive response.

How single-bodied intelligent pigs change what is inspectable

Based on more than 20 years of continuous development, Cokebusters’ patented single-module intelligent pig is a compact, battery-powered, bi-directional inspection tool. Transducers, control electronics, power supply and alignment appendages are all built into one assembly, so it can navigate tight bends, diameter transitions and restricted access points that defeat conventional tools.

  • Inspects pipelines from 2.5″ to 12″ internal diameter
  • Deploys through existing access points and in-line pig valves, such as those used for cleaning or batch separation
  • Needs minimal or no modification to pipeline infrastructure
  • Brings assets into a full integrity programme without significant capital investment or operational disruption

Find out more about our in-line inspection service for pipelines and the UT AXIS smart pig.

What an unpiggable pipeline inspection measures

Using pulse-echo ultrasonic inspection, the intelligent pig gathers high-density internal radius and wall thickness measurements. It can identify and quantify:

  • Internal and external wall loss
  • Fretting damage
  • Creep deformation
  • Internal fouling such as petroleum coke or scale
  • Areas of pitting corrosion
  • Historic repairs and schedule changes
  • Dents, bore restrictions and other geometric anomalies

Data can be presented numerically, graphically and as C-scan visualisations.

Knowing exactly where every reading was taken

The UT AXIS smart pig adds an integrated odometer to the single-bodied tool. Spring-loaded arms with rubber-tread wheels and triple cross-verification logic log axial position continuously, so every ultrasonic reading is tied to a specific physical location on the pipeline. That turns inspection data into a position-referenced integrity map, making it faster to pinpoint defects, target excavation or maintenance, and compare results over time.

The odometer-equipped smart pig has been deployed on complex, multi-phase carbon steel pipelines with no conventional launcher or receiver, delivering a continuous axial log and a complete ultrasonic dataset despite challenging bends, tees and changes in elevation.

Clean, inspect and verify in one operation

Pipeline inspection is often delivered as part of an integrated programme. Combining mechanical pipeline cleaning with in-line inspection means a pipeline can be cleaned, inspected and verified in a single coordinated operation, with mechanical cleaning operators and inspection technicians working together on site. Inspection data confirms bore condition and validates how effective the cleaning has been. Learn more about cleanliness verification.

From inspection data to integrity decisions

Inspection results feed directly into fitness for service and remaining life assessments in accordance with API 579 / ASME FFS-1, as well as digital integrity databases and risk-based inspection programmes. Data is interpreted using Roxtail™ and can be explored in 3D with InsightVision Enterprise.

Case studies

Further reading

Unpiggable pipeline inspection FAQs

What is an unpiggable pipeline?

A pipeline that cannot be inspected with conventional multi-bodied in-line inspection tools, usually because of diameter or schedule changes, tight bends, branches and tie-ins, short lengths, no launch and receive facilities, or poor economics.

Can an unpiggable pipeline be inspected without modification?

In many cases, yes. Cokebusters’ compact single-bodied intelligent pig can be deployed through existing access points and in-line pig valves, with minimal or no modification to the pipeline.

What pipe sizes can be inspected?

Cokebusters inspects pipelines ranging from 2.5″ to 12″ internal diameter.

What defects can the inspection detect?

Internal and external wall loss, fretting, creep deformation, internal fouling such as coke or scale, pitting corrosion, historic repairs, schedule changes, dents and other geometric anomalies.

How are defects located along the pipeline?

The UT AXIS smart pig has an integrated odometer that continuously logs axial position, so every ultrasonic reading is linked to a precise location on the asset.

Talk to us about your unpiggable assets

If you have pipelines or process tubing that have been left out of your inspection regime, we would welcome the chance to assess whether they still need to be. Contact our team to find out more.